- Home
- Flooring guide
- Subfloor
How to prepare the subfloor for vinyl (LVT) flooring
The subfloor for vinyl floors must be dry, firm, level, clean and free of cracks. First the concrete moisture is measured, dust and weak spots are removed, the subfloor is primed and, if necessary, levelled with a levelling compound. A thin vinyl floor reproduces every unevenness, so preparation determines the final result.
What manufacturers require
The Hamat IDENTITY installation instructions state clearly: always check that the subfloor is permanently dry, free of cracks, clean, resistant to tension and compression, and level. The Kiilto Extra datasheet sets the same requirements: dry, firm, level, free of dust and grease.
| Indicator | Limit | Source |
|---|---|---|
| Concrete moisture for gluing | Max. 3.5 w-% or 85 % RH | Kiilto Extra, Grip, Pro Grip |
| Moisture of a wooden subfloor | 8–12 % | Kiilto Extra |
| Concrete moisture for levelling | < 90 % RH | Kiilto Optio, Maxirapid, Easyrapid |
| Temperature during gluing | +18–25 °C | Kiilto Extra |
| Climate during IDENTITY installation | About 18 °C, air humidity ≤ 70 % | Hamat |
Subfloor preparation step by step
- Assess the subfloorWe inspect for cracks, weak spots, remnants of old adhesive or paint, and measure levelness.
- Measure the moistureWe measure concrete moisture before every gluing job. If the limit is exceeded, the adhesive may not stick and the flooring may deform.
- Sand and vacuumKiilto instructs to sand rough and uneven spots and high concrete ridges, remove cement dust and paint residue, and vacuum thoroughly.
- PrimeBefore Kestonit Optio, concrete is primed with Kiilto Start Primer, diluted 1:4. Construction boards – undiluted. For non-absorbent surfaces, such as ceramic tiles or painted floors, Kiilto Fix Primer is suitable.
- LevelWe choose the compound by layer thickness: Easyrapid 0–5 mm, Kestonit Optio 3–20 mm, Maxirapid 1–30 mm for local repairs and slopes.
- Let it dryEasyrapid can be covered after 1–2 h, Maxirapid after about 2 h, Optio after 1 day at a 10 mm layer and after 3 days at 20 mm (23 °C, 50 % RH).
- Check before installationThe surface must be clean, dust-free and dry. Only then is the flooring glued or laid.
Why it is worth levelling even "good" concrete
The Kestonit Optio datasheet states that a layer of low-alkali levelling compound protects the adhesive and the vinyl flooring from the effect of alkaline moisture in the concrete, and studies have shown that a 5 mm layer gives a protective effect. The Kiilto Extra and Kiilto Grip datasheets also recommend levelling concrete with a low-alkali compound.
For click, glued and self-adhesive floors
- Click (ADORE®). No adhesive is needed, but a level subfloor is essential – the locks must engage along their full length.
- Glued (IDENTITY). The requirements are the strictest: the thin 2.5 mm layer reproduces every unevenness, and the adhesive needs a dry, primed, clean subfloor.
- Self-adhesive (Majestik). The adhesive layer needs a level, clean, dust-free surface.
Different subfloors – different solutions
| Subfloor | What we do | Materials |
|---|---|---|
| New concrete or cement screed | We measure moisture, sand, prime, level | Start Primer 1:4, Kestonit Optio |
| Old ceramic tiles | We check adhesion, prime the non-absorbent surface, fill the joints and level | Fix Primer or undiluted Start Primer, Easyrapid or Optio |
| Painted floors | We remove weak layers and prime | Fix Primer |
| Construction boards | We prime with undiluted primer and level the joints | Start Primer (undiluted) |
| Floors with old adhesive residue | We mechanically remove weak residue and prime | Start Primer (undiluted) |
| Holes, slopes, damage | Local repairs before levelling the whole area | Maxirapid 1–30 mm |
Kiilto states that levelling must be done no later than 24 hours after priming. For construction boards, non-absorbent surfaces and surfaces with old adhesive residue, Start Primer must dry for about 2 hours, Fix Primer – about 1 hour.
Room climate
The subfloor is not the only condition. Hamat recommends acclimatising IDENTITY flooring in the room for at least 24 hours, keeping it on a level surface and working at about 18 °C and air humidity of no more than 70 %. For Kiilto Extra adhesive, a working temperature of +18–25 °C is specified, and for levelling compounds – an optimum of +18–20 °C and not below +10 °C. Direct sunlight should also be avoided.
What you can check yourself
- Whether there are no visible cracks or crumbling areas in the subfloor.
- Whether tapping the subfloor produces no hollow sound – it may indicate a delaminated layer.
- Whether the surface does not leave dust when you run a hand over it.
- Whether a long straight edge placed on the floor touches the surface everywhere.
- Whether there is any paint, wax or old adhesive residue on the subfloor.
This check helps you prepare, but only measurements can reliably assess moisture and levelness. We carry them out on site.
Calculate the levelling compoundEnter the area and layer thickness – the tool will calculate the number of bags and the amount of primer.IDENTITY floors, for which the subfloor matters most
Glue-down vinyl flooring Element Dryback 8010
Glue-down vinyl flooring Element Dryback 8020
Glue-down vinyl flooring Element Dryback 8030
Glue-down vinyl flooring Element Dryback 8040
The essentials in brief
- The subfloor must be dry, firm, level, clean and free of cracks.
- Concrete moisture for gluing – max. 3.5 w-% or 85 % RH.
- The primer is chosen according to the surface: Start Primer for absorbent, Fix Primer for non-absorbent.
- The compound is chosen by layer thickness: Easyrapid 0–5 mm, Optio 3–20 mm, Maxirapid for local repairs.
In brief about this
Can vinyl be laid over old tiles?
Often possible if the tiles are firmly attached. The joints are levelled and the non-absorbent surface is primed, e.g. with Kiilto Fix Primer. We decide only after assessing the subfloor.
How long does the levelling compound take to dry?
It depends on the compound and thickness: Easyrapid can be covered after 1–2 h, Maxirapid after about 2 h, Kestonit Optio after 1 day at a 10 mm layer.
Is priming needed before Easyrapid?
Kiilto states that priming of a concrete or levelling-compound subfloor before Easyrapid is not needed. Renovated surfaces and boards must be primed with undiluted Start Primer.
What moisture level of concrete is permitted?
For Kiilto adhesives – max. 3.5 w-% or 85 % RH; for levelling compounds – less than 90 % RH.